Sena HD1100 Instrukcja Użytkownika

Starter Kit and User Manual for the HelloDevice 1100 Version 1.1

Starter Kit and User Manual for the HelloDevice 1100 7 3.5 Flash Memory Web page resources files that the user creates to control the user device a

Starter Kit and User Manual for the HelloDevice 1100 8 4. Setting Up the Hardware The HelloDevice 1100 is as follows: § Install the HelloDevice

Starter Kit and User Manual for the HelloDevice 1100 9 The setup program will automatically be installed onto c:\Program Files\HelloDevice utility f

Starter Kit and User Manual for the HelloDevice 1100 10 4.2 Connecting Hardware (1) Connect the 5V DC power supply adaptor to the HelloDevice and p

Starter Kit and User Manual for the HelloDevice 1100 11 4.3 Configuring Network In order for a HelloDevice to function as a server on the network,

Starter Kit and User Manual for the HelloDevice 1100 12 Setting an IP address with the HelloDevice Utility Software: (1) Run the HelloDevice Utilit

Starter Kit and User Manual for the HelloDevice 1100 13 (5) Check the status of Tx LED on HelloDevice. The HelloDevice Utility Software will send a

Starter Kit and User Manual for the HelloDevice 1100 14 verifies that the HelloDevice works successfully as a web server. Figure 4.9 HelloDevice

Starter Kit and User Manual for the HelloDevice 1100 15 Remove the corresponding item to the current HelloDevice information by using the following

Starter Kit and User Manual for the HelloDevice 1100 16 5. Quick Tour This chapter describes how to build a homepage on the HelloDevice web server

Starter Kit and User Manual for the HelloDevice 1100 Version 1.0 Last revised on July 16, 2000-07-16 Printed in Korea Copyright Copyright 2000,

Starter Kit and User Manual for the HelloDevice 1100 17 stored on the flash memory. Since the HelloDevice does not use a general operating ststems,

Starter Kit and User Manual for the HelloDevice 1100 18 Figure 5.3. Finding Web server demo files (3) Select a file name to build. Figure 5.4.

Starter Kit and User Manual for the HelloDevice 1100 19 Figure 5.5. Entering the IP address to upload the built files (5) Click the [Target file]

Starter Kit and User Manual for the HelloDevice 1100 20 (7) Enter URL http://192.168.1.15/index.html in the web browser, and try connecting. The w

Starter Kit and User Manual for the HelloDevice 1100 21 The HelloDevice 1100 Starter Kit provides a Demo Board and sample programs for demonstratin

Starter Kit and User Manual for the HelloDevice 1100 22 5.2.2 Web Demonstration Use the sample Web files located in the “IODemo” folder in HelloD

Starter Kit and User Manual for the HelloDevice 1100 23 (3) When uploading is completed, run the Web browser and connect to the http://192.168.1.15

Starter Kit and User Manual for the HelloDevice 1100 24 Figure 5.12. Relationship between the digital I/O demo screen and Demo Board

Starter Kit and User Manual for the HelloDevice 1100 25 6. Connecting User Devices The I/O control commands are transferred to the HelloDevice thr

Starter Kit and User Manual for the HelloDevice 1100 26 Chapter 6.1 will describe the HelloDevice communication protocol; Chapter 6.2 will describe

Table of Contents 1. Before You Start 2. Overview 3. Main Board Specifications 3.1. Power Supply 3.2. Microprocessor 3.3. Ethernet Interface

Starter Kit and User Manual for the HelloDevice 1100 27 The status value of I/O monitor command and response depends on user’s design of the hardwar

Starter Kit and User Manual for the HelloDevice 1100 28 Number of Byte Type 1 2 3 Output status control command 0x76 Output Contact Point Status

Starter Kit and User Manual for the HelloDevice 1100 29 The power for the demo board is supplied from the HelloDevice through Vcc/GND pin of 20-pin

Starter Kit and User Manual for the HelloDevice 1100 30 Figure 6.6. Circuit diagram of the HelloDevice I/O control board

Starter Kit and User Manual for the HelloDevice 1100 31 6.2.2 Implementing your Hardware 1) Connection to the HelloDevice The user can directly con

Starter Kit and User Manual for the HelloDevice 1100 32 P24G24Hello Device VccK1DSP1a-DC24V4316D11N41481 2Q3KTD1028123ISO19PC8171243LED?LED RED1 2R2

Starter Kit and User Manual for the HelloDevice 1100 33 (struct sockaddr*)&clientAddr, sizeof(clientAddr) ) ; if (err == -1

Starter Kit and User Manual for the HelloDevice 1100 34 commandBuf[0] = IOSet ; commandBuf[1] = (BYTE) ((IOStatus[2] >> 8) & 0x000000f

Starter Kit and User Manual for the HelloDevice 1100 35 data[0] = COMMAND_SET; data[1] = (byte) ((outdata >> 8) & 0x000000ff); data[

Starter Kit and User Manual for the HelloDevice 1100 36 Appendix A. IP address configuration by using cross-over Ethernet cable You may configure t

Starter Kit and User Manual for the HelloDevice 1100 1 1. Before You Start. § Items supplied in the HelloDevice 1100 Starter Kit Items Piece(s)

Starter Kit and User Manual for the HelloDevice 1100 37 3) Configure the network environment set-up of your PC so that it can communicate with the

Starter Kit and User Manual for the HelloDevice 1100 2 2. Overview The HelloDevice is a connectivity solution that allows any device in any industr

Starter Kit and User Manual for the HelloDevice 1100 3 3. Main Board Specifications The hardware configuration and the system block diagram of the

Starter Kit and User Manual for the HelloDevice 1100 4 3.1 Power Supply § Voltage supply = 5V DC ±10% § Current supply = 200mA or lower 3.2 Micr

Starter Kit and User Manual for the HelloDevice 1100 5 Pin No. Description Red Line 1 Tx+ White with orange 2 Tx- Orange 3 Rx+ White with

Starter Kit and User Manual for the HelloDevice 1100 6 3.4 Digital I/O Interface The digital I/O interface of the HelloDevice 1100 is equipped with