Sena ProBee-ZU10 Instrukcja Użytkownika

1ProBee-ZU10 User Guide Rev.1.5ZigBee USB AdapterProBee-ZU10User GuideSena Technologies, Inc.Rev 1.5

10ProBee-ZU10 User Guide Rev.1.5Applications Advanced Metering Infrastructure HomeArea Networks (HAN) Neighborhood Area Networks (NAN) HomeAutomat

11ProBee-ZU10 User Guide Rev.1.52 Getting StartedCreating a ZigBee network using the ZU10 adapters consists of the following steps: Connect the ZU10

12ProBee-ZU10 User Guide Rev.1.52.1.2 USB Driver InstallationIn case the USB interface is used for the communication between the development board and

13ProBee-ZU10 User Guide Rev.1.5after the input released again. If this input is pressed while the ZU10 starts, the local node entersbootloader menu a

14ProBee-ZU10 User Guide Rev.1.5Figure 2-4 Testing AT Command on HyperTerminal2.4 Using ProBee Manager for ConfigurationIt is possible to set or get t

15ProBee-ZU10 User Guide Rev.1.5Figure 2-6 ProBee Manager Main WindowClicking ‘Reboot’ button reboots the local node. Users can reload and refresh the

16ProBee-ZU10 User Guide Rev.1.5in order not lose it moving to other properties. To apply changes, please reboot the device by clicking‘Reboot’ button

17ProBee-ZU10 User Guide Rev.1.5To export the configuration, please follow the steps as below: Click the ‘Export’ button at the ‘Configuration Manage

18ProBee-ZU10 User Guide Rev.1.5To update firmware at local node, please follow the steps as below: Select a firmware file to update at the ‘Firmware

19ProBee-ZU10 User Guide Rev.1.53 ZigBee Network ConfigurationA ZigBee Network consists of a coordinator, routers and end-devices. A minimal ZigBee ne

2ProBee-ZU10 User Guide Rev.1.5ProBee-ZU10 User GuideFirmware version PTv1.XCopyrightCopyright 2010 ~ 2012, Sena Technologies, Inc. All rights reserve

20ProBee-ZU10 User Guide Rev.1.5 Configure the ZU10 node type as the coordinator Optionally, select the channel mask. Otherwise, the ZU10 will use t

21ProBee-ZU10 User Guide Rev.1.5Table 3-2 Channel BitmaskChannel 12 13 14 15 16 17 18Bit mask 00001000 00002000 00004000 00008000 00010000 00020000 00

22ProBee-ZU10 User Guide Rev.1.5AT+PERMIT=255 or AT+PJ=255The user can permit joining for a moment at need. The AT command to permit joining isAT+PERM

23ProBee-ZU10 User Guide Rev.1.5Example)AT+NODETYPE=2<CR> # Select router modeOK<CR> # ResponseATZ<CR> # Apply the changeOK<CR>

24ProBee-ZU10 User Guide Rev.1.5 Configure the ZU10 node type as an end-device Optionally, select the channel mask. Otherwise, the ZU10 will use the

25ProBee-ZU10 User Guide Rev.1.5 Optionally, set up the PAN ID and/or the extended PAN ID. Otherwise, the ZU10 will scan and jointhe ZigBee network f

26ProBee-ZU10 User Guide Rev.1.5Figure 3-1 Sleep Interval and Wake-up TimingThe sleepy end-device can also wake up from the sleep mode by incoming ser

27ProBee-ZU10 User Guide Rev.1.53.5.1 Security LevelIn order to use security in the application, a user should set security level using the AT command

28ProBee-ZU10 User Guide Rev.1.5responding to the message to indicate the channel change by the network manager. Because ProBee-ZE20S can be a network

29ProBee-ZU10 User Guide Rev.1.54 Data TransmissionThe ZU10 supports three different types of data transmissions: unicast, multicast and broadcast. Un

3ProBee-ZU10 User Guide Rev.1.5Revision HistoryRevision Date Name DescriptionV1.0.0 2010-09-30 KS Choi Initial WritingV1.1.0 2010-10-27 KS Choi Modifi

30ProBee-ZU10 User Guide Rev.1.5AT+MULTICAST=<group_id>,<MSG><CR> or AT+MC=<group_id>,<MSG><CR>, where <group_i

31ProBee-ZU10 User Guide Rev.1.5the same rules.4.1.4 Sending Binary DataBecause some characters like carriage return, line feed and back space collide

32ProBee-ZU10 User Guide Rev.1.5+0001950000000001| abc\0D<CR>Note: In PTv1.2 or earlier version, only the characters mentioned at Table 4-1 are

33ProBee-ZU10 User Guide Rev.1.5ATD<value><CR>Set unicast data mode to <value> device and <value> can be either 16-bit node ID

34ProBee-ZU10 User Guide Rev.1.5OK<CR> # ResponseSend unicast msg # Put the unicast message+++ # Leave data modeOK<CR> # ResponseATD0000&l

35ProBee-ZU10 User Guide Rev.1.54.2.2 Multicast Data ModeMulticast data mode can be used for continuous data transmission to a particular group of mul

36ProBee-ZU10 User Guide Rev.1.5broadcast one packet over 2 seconds for safe transmission. Broadcast transmission failure also causesretransmission wh

37ProBee-ZU10 User Guide Rev.1.5Broadcast data mode can be entered using either ATB or AT+TRANSMITMODE=3. If ATB command isused, the device will enter

38ProBee-ZU10 User Guide Rev.1.5+++ # Leave data modeOK<CR> # ResponseAT+TRANSMITMODE=3<CR> # Set transmission mode to current networkOK&l

39ProBee-ZU10 User Guide Rev.1.55 AT Command Reference5.1 Command Line FormatEach command line is composed of a prefix, body and terminator. Only “AT”

4ProBee-ZU10 User Guide Rev.1.5Contents1 INTRODUCTION...

40ProBee-ZU10 User Guide Rev.1.55.2.4 ATEDescription Echo(1) or No Echo(0).Execute ATE<number><CR>Response OK<CR>5.2.5 ATMDescriptio

41ProBee-ZU10 User Guide Rev.1.55.2.11 +++Description Interrupt data mode. “+++” must be entered within 500ms.Execute +++Response OK<CR>5.3 Node

42ProBee-ZU10 User Guide Rev.1.55.3.5 AT+OPPANID or AT+OIDescriptionGet the operating 16-bit PAN ID. If PAN ID is set specific value not 0s, operating

43ProBee-ZU10 User Guide Rev.1.5Range 00001000 - 03FFF0005.4.2 AT+PANID or AT+PIDescriptionGet/Set the 16-bit PAN ID. If it is set to 0s at a coordina

44ProBee-ZU10 User Guide Rev.1.55.4.6 AT+STACK or AT+ZSDescriptionGet/Set the ZigBee stack profile value. This value must be set the same on all devic

45ProBee-ZU10 User Guide Rev.1.55.5.3 AT+DSCAN or AT+DSDescriptionPerform a scanning for existing nodes in the current network. A coordinator or route

46ProBee-ZU10 User Guide Rev.1.55.5.6 AT+PERMIT or AT+PJDescriptionPermit other nodes to join the network. (0~254s, 255=continuance) An end-devicecann

47ProBee-ZU10 User Guide Rev.1.55.7 Data Transmission and Reception5.7.1 AT+DESTLA or AT+DLDescription Get/Set the 64-bit destination IEEE address for

48ProBee-ZU10 User Guide Rev.1.5Range 0 - 45.7.6 AT+UNICAST or AT+UCDescriptionSend unicast message to specific node using long or short address of re

49ProBee-ZU10 User Guide Rev.1.5Execute AT+LINKKEY?<CR> AT+LINKKEY=<value><CR>Response<value><CR>OK<CR>OK<CR>

5ProBee-ZU10 User Guide Rev.1.54.1 Command Mode...

50ProBee-ZU10 User Guide Rev.1.55.9.3 AT+PARITY or AT+UPDescription Get/Set the serial parity setting on the module.Execute AT+PARITY?<CR> AT+PA

51ProBee-ZU10 User Guide Rev.1.55.10.2 AT+HELP or AT+HPDescription Show all the available commandsExecute AT+HELP<CR>ResponseAvailable AT Comman

52ProBee-ZU10 User Guide Rev.1.56 AT Command Examples6.1 Network configuration6.1.1 CoordinatorAT+NODETYPE=1<CR> # set node type (coordinator)OK

53ProBee-ZU10 User Guide Rev.1.500019500002FDC15OK # ResponseAT+REMOTE=1FEF,AT+LONGADDR<CR> # get 64-bit address of remote node (1FEF)0001950000

54ProBee-ZU10 User Guide Rev.1.5OK # Response# send broadcast message(MSG04) to current network and the range isdetermined by S35.AT+BROADCAST=MSG04&l

55ProBee-ZU10 User Guide Rev.1.5ATZ<CR> # Apply the changeOK # ResponseAT+NWKKEY=0<CR> # set the 128-bit network key (random key)OK # Resp

56ProBee-ZU10 User Guide Rev.1.56.5.2 Remote Node# upload firmware to a remote node using 64-bit long address. Note that UARTof local node should be s

57ProBee-ZU10 User Guide Rev.1.57 S-RegistersRegister number Descriptions1112132122233132333435363738395152535455566162Display incoming message in com

58ProBee-ZU10 User Guide Rev.1.57.1.2 S12Description Get/Set the command echo mode.Execute ATS12?<CR> ATS12=<value><CR>Response<v

59ProBee-ZU10 User Guide Rev.1.5range.Execute ATS23?<CR> ATS23=<value><CR>Response<value><CR>OK<CR>OK<CR>Def

6ProBee-ZU10 User Guide Rev.1.55.4.6 AT+STACK or AT+ZS...

60ProBee-ZU10 User Guide Rev.1.57.3.4 S34DescriptionGet/Set the indirect transmission timeout in milliseconds. It is the maximum amount oftime that th

61ProBee-ZU10 User Guide Rev.1.5Execute ATS37?<CR> ATS37=<value><CR>Response<value><CR>OK<CR>OK<CR>Default 0

62ProBee-ZU10 User Guide Rev.1.5the sleepy end-device to poll more rapidly for a short time when receiving RF data.Execute ATS52?<CR> ATS52=<

63ProBee-ZU10 User Guide Rev.1.57.4.6 S56DescriptionGet/Set the end-device poll period in seconds. Adaptive polling may allow the end-device to poll m

64ProBee-ZU10 User Guide Rev.1.58 Mechanical Drawings

65ProBee-ZU10 User Guide Rev.1.59 Warranty9.1 GENERAL WARRANTY POLICYSena Technologies, Inc. (hereinafter referred to as SENA) warrants that the Produ

66ProBee-ZU10 User Guide Rev.1.59.3 HARDWARE PRODUCT WARRANTY DETAILSWARRANTY PERIOD: SENA warranties embedded hardware Product for a period of one (1

67ProBee-ZU10 User Guide Rev.1.510 Regulatory Information10.1 FCCFCC Rule: Part 15 Subpart C Section 15.247FCCID: S7AZBLINXZU10FCC Compliance Statemen

68ProBee-ZU10 User Guide Rev.1.510.2 CECE1177(!)We, Sena Technologies, Inc., declare that the product(s): ProBee-ZU10 ZigBee USB Adapterto which this

69ProBee-ZU10 User Guide Rev.1.511 RF InformationRadio Frequency Range2.410~2.475GHzNumber of Frequency Channel14 channelsTransmission MethodDSSS (Dir

7ProBee-ZU10 User Guide Rev.1.56 AT COMMAND EXAMPLES...526.1 Network c

8ProBee-ZU10 User Guide Rev.1.57.4.4 S54.......

9ProBee-ZU10 User Guide Rev.1.51 Introduction1.1 About This DocumentThis document provides an introduction on configuration and operation of the ProBe