Sena ProBee-ZS10 Instrukcja Użytkownika

1ProBee-ZS10 User Guide Rev.1.5 ZigBee Serial Adapter ProBee-ZS10 User Guide Sena Technologies, Inc. Rev 1.5.1

10ProBee-ZS10 User Guide Rev.1.5Applications • Advanced Metering Infrastructure • Home Area Networks (HAN) • Neighborhood Area Networks (NAN) • Home

11ProBee-ZS10 User Guide Rev.1.52 Getting Started Creating a ZigBee network using the ZS10 adapters consists of the following steps: • Connect a p

12ProBee-ZS10 User Guide Rev.1.5 2.1.2 Connecting the panel Please connect the device to your computer directly or using serial cable so AT commands

13ProBee-ZS10 User Guide Rev.1.52.1.4 Attaching Battery Pack to ZS10 The ZS10 also supports optional standard battery pack (240mAh) and extended bat

14ProBee-ZS10 User Guide Rev.1.5Step2. Slide the battery pack into the ZS10 slot. Figure 2-6 Attach the battery pack Step3. Fasten the battery pa

15ProBee-ZS10 User Guide Rev.1.5Table 2-1 The ProBee-ZS10 LED Indicators LED Description Power Power LED turns ON when power is supplied. If the nod

16ProBee-ZS10 User Guide Rev.1.5 Upper 3 dipswitches are used for setting the baud rate, and bottom dipswitch is used for setting data bit, parity, s

17ProBee-ZS10 User Guide Rev.1.5 Figure 2-9 HyperTerminal Serial Settings To display the AT commands that are being typed, you need to enable the lo

18ProBee-ZS10 User Guide Rev.1.52.4 Using ProBee Manager for Configuration It is possible to set or get the configurations of the ZS10 using ProBee

19ProBee-ZS10 User Guide Rev.1.5Clicking ‘Reboot’ button reboots the local node. Users can reload and refresh the recent configuration of the local n

2ProBee-ZS10 User Guide Rev.1.5ProBee-ZS10 User Guide Firmware version PTv1.X Copyright Copyright 2010 ~ 2012, Sena Technologies, Inc. All rights re

20ProBee-ZS10 User Guide Rev.1.5To connect to local node through serial port, please follow the steps as below: z Click the ‘…’ button at ‘Remote Co

21ProBee-ZS10 User Guide Rev.1.5 The Firmware Update Pane appears when the ‘Firmware Update’ tab is selected. The ‘Message’ section displays informat

22ProBee-ZS10 User Guide Rev.1.53 ZigBee Network Configuration A ZigBee Network consists of a coordinator, routers and end-devices. A minimal ZigBe

23ProBee-ZS10 User Guide Rev.1.5 • Configure the ZS10 node type as the coordinator • Optionally, select the channel mask. Otherwise, the ZS10 will

24ProBee-ZS10 User Guide Rev.1.5 Table 3-2 Channel Bitmask Channel 12 13 14 15 16 17 18 Bit mask 00001000 00002000 00004000 00008000 00010000 000200

25ProBee-ZS10 User Guide Rev.1.5AT+PERMIT=255 or AT+PJ=255 The user can permit joining for a moment at need. The AT command to permit joining is A

26ProBee-ZS10 User Guide Rev.1.5Example) AT+NODETYPE=2<CR> # Select router mode OK<CR> # Response ATZ<CR> # Apply the

27ProBee-ZS10 User Guide Rev.1.5 • Configure the ZS10 node type as an end-device • Optionally, select the channel mask. Otherwise, the ZS10 will us

28ProBee-ZS10 User Guide Rev.1.5• Configure the ZS10 node as a sleepy end-device. • Optionally, select the channel mask. Otherwise, the ZS10 will u

29ProBee-ZS10 User Guide Rev.1.5Poll Request Data Exchange Parent Node Sleepy End-Device Sleep Wake-Up Sleep S53 S52S54 Figure 3-1 Sleep Interval an

3ProBee-ZS10 User Guide Rev.1.5Revision History Revision Date Name Description V1.0.0 2010-09-30 KS Choi Initial Writing V1.1.0 2010-10-27 KS

30ProBee-ZS10 User Guide Rev.1.5 3.5.1 Security Level In order to use security in the application, a user should set security level using the AT comm

31ProBee-ZS10 User Guide Rev.1.5responding to the message to indicate the channel change by the network manager. Because ProBee-ZE20S can be a networ

32ProBee-ZS10 User Guide Rev.1.54 Data Transmission The ZS10 supports three different types of data transmissions: unicast, multicast and broadcast.

33ProBee-ZS10 User Guide Rev.1.5AT+MULTICAST=<group_id>,<MSG><CR> or AT+MC=<group_id>,<MSG><CR> , where <group

34ProBee-ZS10 User Guide Rev.1.5the same rules. 4.1.4 Sending Binary Data Because some characters like carriage return, line feed and back space co

35ProBee-ZS10 User Guide Rev.1.5 +0001950000000001| abc\0D<CR> Note: In PTv1.2 or earlier version, only the characters mentioned at Table 4-1

36ProBee-ZS10 User Guide Rev.1.5ATD<value><CR> Set unicast data mode to <value> device and <value> can be either 16-bit node

37ProBee-ZS10 User Guide Rev.1.5OK<CR> # Response Send unicast msg # Put the unicast message +++ # Leave data mode OK<CR>

38ProBee-ZS10 User Guide Rev.1.54.2.2 Multicast Data Mode Multicast data mode can be used for continuous data transmission to a particular group of

39ProBee-ZS10 User Guide Rev.1.5broadcast one packet over 2 seconds for safe transmission. Broadcast transmission failure also causes retransmission

4ProBee-ZS10 User Guide Rev.1.5Contents 1 INTRODUCTION...

40ProBee-ZS10 User Guide Rev.1.5 Broadcast data mode can be entered using either ATB or AT+TRANSMITMODE=3. If ATB command is used, the device will en

41ProBee-ZS10 User Guide Rev.1.5+++ # Leave data mode OK<CR> # Response AT+TRANSMITMODE=3<CR> # Set transmission mode to cur

42ProBee-ZS10 User Guide Rev.1.55 AT Command Reference 5.1 Command Line Format Each command line is composed of a prefix, body and terminator. Onl

43ProBee-ZS10 User Guide Rev.1.55.2.4 ATE Description Echo(1) or No Echo(0). Execute ATE<number><CR> Response OK<CR> 5.2.5 ATM De

44ProBee-ZS10 User Guide Rev.1.55.2.11 +++ Description Interrupt data mode. “+++” must be entered within 500ms. Execute +++ Response OK<CR> 5

45ProBee-ZS10 User Guide Rev.1.55.3.5 AT+OPPANID or AT+OI Description Get the operating 16-bit PAN ID. If PAN ID is set specific value not 0s, operat

46ProBee-ZS10 User Guide Rev.1.5Range 00001000 - 03FFF000 5.4.2 AT+PANID or AT+PI Description Get/Set the 16-bit PAN ID. If it is set to 0s at a coo

47ProBee-ZS10 User Guide Rev.1.55.4.6 AT+STACK or AT+ZS Description Get/Set the ZigBee stack profile value. This value must be set the same on all de

48ProBee-ZS10 User Guide Rev.1.55.5.3 AT+DSCAN or AT+DS Description Perform a scanning for existing nodes in the current network. A coordinator or ro

49ProBee-ZS10 User Guide Rev.1.55.5.6 AT+PERMIT or AT+PJ Description Permit other nodes to join the network. (0~254s, 255=continuance) An end-device

5ProBee-ZS10 User Guide Rev.1.53.5.2 Link Key...

50ProBee-ZS10 User Guide Rev.1.55.7 Data Transmission and Reception 5.7.1 AT+DESTLA or AT+DL Description Get/Set the 64-bit destination IEEE addres

51ProBee-ZS10 User Guide Rev.1.5Range 0 - 4 5.7.6 AT+UNICAST or AT+UC Description Send unicast message to specific node using long or short address

52ProBee-ZS10 User Guide Rev.1.5Execute AT+LINKKEY?<CR> AT+LINKKEY=<value><CR> Response <value><CR> OK<CR> OK<

53ProBee-ZS10 User Guide Rev.1.55.9.3 AT+PARITY or AT+UP Description Get/Set the serial parity setting on the module. Execute AT+PARITY?<CR>

54ProBee-ZS10 User Guide Rev.1.55.10.2 AT+HELP or AT+HP Description Show all the available commands Execute AT+HELP<CR> Response Available AT

55ProBee-ZS10 User Guide Rev.1.56 AT Command Examples 6.1 Network configuration 6.1.1 Coordinator AT+NODETYPE=1<CR> # set node type (c

56ProBee-ZS10 User Guide Rev.1.500019500002FDC15 OK # Response AT+REMOTE=1FEF,AT+LONGADDR<CR> # get 64-bit address of remote node (1FEF

57ProBee-ZS10 User Guide Rev.1.5OK # Response # send broadcast message(MSG04) to current network and the range is determined by S35. AT+BROAD

58ProBee-ZS10 User Guide Rev.1.5ATZ<CR> # Apply the change OK # Response AT+NWKKEY=0<CR> # set the 128-bit network key

59ProBee-ZS10 User Guide Rev.1.5 6.5.2 Remote Node # upload firmware to a remote node using 64-bit long address. Note that UART of local node should

6ProBee-ZS10 User Guide Rev.1.55.4 Network Specific Parameters ...

60ProBee-ZS10 User Guide Rev.1.57 S-Registers Register number Descriptions 11 12 13 14 21 22 23 31 32 33 34 35 36 37 38 39 51 52 53 54 55 56 61 62

61ProBee-ZS10 User Guide Rev.1.57.1.2 S12 Description Get/Set the command echo mode. Execute ATS12?<CR> ATS12=<value><CR> Respons

62ProBee-ZS10 User Guide Rev.1.57.2.2 S22 Description Get/Set the timeout to permit joining. It determines the time in seconds that the device will a

63ProBee-ZS10 User Guide Rev.1.5Range 0 – 99 7.3.3 S33 Description Get/Set the transmission timeout in milliseconds. A sender retransmits data pack

64ProBee-ZS10 User Guide Rev.1.5be delivered to all nodes within this number of hops of the sender. A value of zero is converted to maximum value(30)

65ProBee-ZS10 User Guide Rev.1.57.4 End-Device 7.4.1 S51 Description Get/Set the poll timeout for a parent node in seconds. If an end-device or a sle

66ProBee-ZS10 User Guide Rev.1.5Range 0 – 10000 7.4.5 S55 Description Get/Set the rejoin timeout. If it is enabled, an end-device tries to rejoin t

67ProBee-ZS10 User Guide Rev.1.5OK<CR> Default 0 Range 0 – 10000

68ProBee-ZS10 User Guide Rev.1.58 Connections 8.1 Serial Port Pin Outs ProBee-ZS10 is a DCE device compatible with the RS232 standard, a DB9 femal

69ProBee-ZS10 User Guide Rev.1.58.2 Serial Wiring Diagram 8.2.1 To Host with DTE Interface 8.2.2 To Host with DCE Interface

7ProBee-ZS10 User Guide Rev.1.55.9.4 AT+STOPBIT or AT+US ...

70ProBee-ZS10 User Guide Rev.1.59 Mechanical Drawings 9.1 ProBee-ZS10 mechanical drawing (mm) 99.8 with stub antenna 16 73.9 without antenna 14.9 30.

71ProBee-ZS10 User Guide Rev.1.5 9.2 Battery pack mechanical drawing (mm) Standard Battery Pack Extended Battery Pack

72ProBee-ZS10 User Guide Rev.1.510 Warranty 10.1 GENERAL WARRANTY POLICY Sena Technologies, Inc. (hereinafter referred to as SENA) warrants that th

73ProBee-ZS10 User Guide Rev.1.510.3 HARDWARE PRODUCT WARRANTY DETAILS WARRANTY PERIOD: SENA warranties embedded hardware Product for a period of on

74ProBee-ZS10 User Guide Rev.1.511 Regulatory Information 11.1 FCC FCC Rule: Part 15 Subpart C Section 15.247 FCCID: S7AZBLINXZS10 FCC Compliance S

75ProBee-ZS10 User Guide Rev.1.511.2 CE CE1177(!) We, Sena Technologies, Inc., declare that the product(s): • ProBee-ZS10 ZigBee Serial Adapter to

76ProBee-ZS10 User Guide Rev.1.512 RF Information Radio Frequency Range 2.410~2.475GHz Number of Frequency Channel 14 channels Transmission Metho

8ProBee-ZS10 User Guide Rev.1.57.3.7 S37.......

9ProBee-ZS10 User Guide Rev.1.51 Introduction 1.1 About This Document This document provides an introduction on configuration and operation of the